The Sampson Build: A Photo Chronicle

Camera roll archaeology: every photo in this build folder still has its original timestamp, so here’s the Sampson build reconstructed in the order it actually happened — from the first look at the bare frame to a finished bike posing in the snow four months later.

October 25 — the starting point

Oct 25, 2025 · 12:32 PM

The Sampson frame, already built up on the stand in the backyard — titanium main triangle, carbon seatstays and top tube panel, “Sampson Attenuation System” cast into the dropout. This was the baseline: a complete bike, but with a black fork and a mismatched cockpit. Sixteen minutes later, a second subject shows up in the photos — a bare, unpainted carbon fork blade, stripped down to raw weave. That’s the tell: the respray project started here, not with the frame, but with the fork.

Sampson titanium frame on a repair stand in the backyard
The Sampson frame as found — titanium front triangle, carbon rear end, black 3T fork.
Bare carbon fork blade stripped to raw weave
Same afternoon: a fork blade stripped bare to the carbon weave. First move in a much longer project.

November 27 — into the paint booth

Nov 27, 2025 · 9:26 AM

A month of stripping and prep later, the fork, an integrated bar/stem, and a saddle go up on jigs inside a plastic-sheeted paint booth. First coat: white epoxy primer, sprayed even and left to tack up on painters’ pyramids.

Fork, bar/stem and saddle in white primer on paint stands
Fork, integrated cockpit, and saddle in white epoxy primer.

December 1 — second primer pass

Dec 1, 2025 · 7:45 PM

Back in the booth for a second white coat — evening session this time, same three parts, same jigs, working toward a uniform base before any color goes down.

Second white primer coat on the cockpit parts
A second, more even white coat before color.

December 8 — red goes on

Dec 8, 2025 · 5:31 PM

Color coat. The fork leg comes out of the booth wet and glossy — a deep candy red laid straight over the white base.

Wet red basecoat on the fork leg
First red basecoat, still wet.

December 14 — the Storm decal shows up

Dec 14, 2025 · 8:19 PM

With the red cured, the original “Storm Racing” saddle graphic gets masked back in — white lettering over the fresh red instead of the tired factory finish it started with.

Storm Racing saddle repainted gloss red with white decal
The saddle, resprayed red with the Storm Racing graphic restored.

December 20-21 — full color, and a name reappears

Dec 20, 2025 · 6:40 PM

Fork, bar/stem, and saddle finally sitting together, all in the same red, all glossy. Over the next two days the “Storm” wordmark gets masked and sprayed onto the bar itself, matching the saddle.

Fork bar and saddle together in matching gloss red
The full set, color-matched.
Storm wordmark masked onto the red handlebar
Masking the Storm wordmark onto the bar.

January 5 — full PPE, and a mirror finish

Jan 5, 2026 · 4:24 PM

A respirator-and-spray-gun selfie mid-session, followed by the payoff: the handlebar/stem unit out of the booth, wet-sanded and polished to a compound-buffed shine on the workbench.

Full respirator and spray gun setup
Full respirator, gravity-feed gun — no shortcuts on ventilation.
Polished red Storm handlebar and stem on cutting mat
Wet-sanded and compound-buffed to a mirror gloss.

January 10-11 — back on the bike

Jan 11, 2026 · 8:22 PM

The finished parts go back onto the Sampson frame indoors — fork first, then the Storm cockpit and saddle. By the night of the 11th the bike is fully reassembled: titanium and carbon frame, gloss-red fork and bar carrying the restored Storm graphics.

Fork and cockpit reinstalled on the Sampson frame
Fork and cockpit going back on the frame.
Fully reassembled Sampson bike with new red cockpit
Reassembled, ten weeks after the first coat of primer.

February 28 — the reveal, in the snow

Feb 28, 2026 · 11:19 AM

The finished bike gets its proper photoshoot — parked in a foot of backyard snow, golden retriever included, camera clicking every few seconds for a solid eight minutes. Titanium frame, red Storm cockpit, black carbon wheels: the whole project laid out in one sitting.

Finished Sampson bike in the snow
The finished build, snow photoshoot.
Finished bike with golden retriever in the snowy backyard
Photobombed, appropriately.
Finished Sampson bike side profile in the snow
Four months from bare carbon to finished build.

Reconstructed from EXIF timestamps on 226 photos in the build folder — no notes, just the camera roll in order.

Leave a Comment